Below you will find out more detailed information about the saber we have listed. As well as some useful tips and advice. The fight for the fate of the galaxy awaits you.
Will you fight for freedom or domination? May the force be with you! Our fantastic v115 is an amazing saber from our core range. The hilt comes in at 27cm and houses the RGB Eco Smoothswing core (Red, Green and Blue) LED. This slick saber comes in a choice of black or blue mixed in with a striking chrome finish.The hilt weighs in at a solid 340g (hilt only) which gives the saber a nice feel to it. Once fully built with the 92cm blade the total length is approx. The saber is made for heavy duelling, spinning, tricks or just looking great on display. The emitter (top of saber) is cut away to show the blade in the hilt. The recharge port and control button are in the centre as well as the LED light which indicates when switch on and blinks when changing the features (see instructions below). The pommel (Bottom of saber) houses the speakers. Please see below for the saber specification as well as detailed instructions and trouble shooting. The light is an LED 12w RGB (red, green and blue) which means you get to choose the colour that you want, whenever you want as the blade cycles through. It comes with a safety protected 3000mAh battery, battery backwards protect system, overload system and over discharge system. The speaker is 2-3watts, 4/8 ohm which gives a fantastic quality. Features include Pre power on, Blaster, Lock up, Flash on clash, 9 sets of sound fonts, Volume adjustment, Light effective adjustment, Music and smooth swing. Blade size is 92cm long, 2mm thick and 1 OD removable bullet tip. Sound fonts are Darth Sidious, Leia, Kylo Ren, Mandalorian Darksaber, General Kenobi, Cal Kestis, Darth Vader, Count Dooku and Rey Skywalker. Press and hold the LED button to bring out of sleep mode. You will hear a "power on" voice and the LED button will turn on. Press and hold the button once, quickly, to turn the blade on. The following controls activate when the blade is on and are based on the flash of the LED button light.
A quick press will initiate a single blaster deflect effect. Press and hold the button for one flash, then release.This will initiate the lockup effect. A quick press will end the lockup effect. Press and hold the button for two flashes, then release. This will initiate the colour cycle.
When the colour you want shows, a quick press will end the cycle. Press and hold the button for 3 flashes to enter the quick colour select. When a colour you like appears, press the button once to exit. Press and hold past three flashes to shut off the blade. While the blade is off, the following controls are activated based on the flash of the LED button light.
This will change the volume. There are 3 settings: Volume high, Volume low and mute. This will change the blade effect. There are 3 blade effects: Steady, Pulse and Unstable. Press and hold the button for three flashes, then release.This will change the sound font to the next selection. Press and continue to hold past the third flash for approximately 10 seconds to put the saber back into sleep mode. It is important that you do not let the battery fully discharge so our advice is to fully charge the saber when it says low battery or if you haven't used it in a while.
Same as RGB apart from. 50w RGB Neopixel Strip in the polycarbonate blade - blade is also 3mm thick.
3600mAh 18650 3.7v safety protected battery. SD card to change sound fonts and carry out firmware updates (updates can be provided on request). Extra features like Fire blade, Rainbow blade, Ghost blade. As well as additional light features (demonstration video available on request). This will initiate the drag effect.
A quick press will end the drag effect. When the colour you want shows, a quick press will end the colour cycle. Continue and hold past two flashes to turn off the blade. There are 5 blade effects: Steady, Pulse, Rainbow blade, Unstable and Fire blade.
This will change the blade mode. There are several blade modes, including some pre on effects. Blade affect will affect pre on's but will not have any affects on Blaster blade and Ghost blade modes. Only blade colour and font selection impact these modes.
Press and hold the button for four flashes, then release. This will change the sound font. The selection of fonts can be customized by the user. There are several motion or manual controls available on the Xenopixel. A direct and quick stabbing motion with the hilt level will turn the blade on or off.
A quick twist while the hilt is pointed down will change the font to the next on the list. Either direction will prompt the change as long as the hilt is pointed downwards. A quick twist while the hilt is pointed up will play a music track, if one or more are available in the selected fonts folder.
A quick twist again will stop the music. Hold the button and impact the hilt/blade to activate lockup. Release the button to end lockup.
While holding the button, a quick twist while the hilt is pointed down will change the selected blade colour. Release the button to select the current colour. While holding the button, a quick twist while the hilt is pointing up will play a special effect. This will also play a sound if the correct file is included in the font.
What to do when you first get your new saber. When you get your new saber, please make sure you put it on charge straight away. While it is on charge have a read of the instructions. It's going to take a few tries to get use to all the features via the control button but when you do it is easy. We are available for help and support if you are having any issues learning how to use the features.
We will send it with the most appropriate courier. We will send the saber within 12 hours of ordering. We hope there are no delays in you receiving your order however we will upload tracking so that you can keep an eye on it. If you have caused some accidental damage, we will still be able to help i. You have snapped the blade we can replace at a discounted price.This product is not suitable for children under the age of 13 unless supervised by an adult to prevent injuries, remember this is not a toy Lightsaber so taking the time to learn how to handle and use the features properly is advised. Fully charge the saber before operating. Use only the included cable with 5v1a USB or 5v Wall charger.
Failure to follow this instruction can result in damaged electronics. A Range Of Colours To Choose From. A Heavy duelling aluminium alloy hilt with a high quality blade. For True Fans Who Appreciate A Quality Saber. We are lightsaber fanatics and love that we get to sell some awesome sabers.We started as an emporium and are transitioning into a lightsaber specialist. Every month we are expanding our range to ensure we have a variety of lightsabers available for quick dispatch from the UK rather than waiting weeks from overseas.
Thanks for stopping by and supporting us on our journey. We deliver to any address in the UK, as well as internationally.
It is in original undamaged packaging with all tags intact. The product is in the same condition as how you received it. You have a statutory duty to take reasonable care of our goods whilst they are in your possession and during transit. His communication is great and he has a good understanding of the buyers perspective when purchasing something so expensive. He is also a really nice guy that makes sure the quality of his products are sublime.
The lightsaber is bright, easy to use and strong. This item is in the category "Collectables\Science Fiction Collectables\Star Wars Collectables\Lightsaber & Weapon Replicas". The seller is "domms_emporium" and is located in this country: GB. This item can be shipped to United Kingdom.