Lightsaber 50w Xenopixel Return of the Jedi Luke Skywalker Version Jedi Cosplay

Lightsaber 50w Xenopixel Return of the Jedi Luke Skywalker Version Jedi Cosplay. The Lightsword - commonly called the saber, known for its glowing blade - is the iconic weapon of great warriors. A wide range of saber toys has been distributed all over the world since the 1970s. Domms Lightsabers sells high-quality, combat-ready sabers that can be used for display, training, or playing our epic battles and duelling. Our goal is simple - to make the dreams of fans a reality everywhere.

Our innovative products come with market-leading features, and we are sure you will enjoy the range available. Below you will find out more detailed information about the saber we have listed.

As well as some useful tips and advice. The fight for the fate of the galaxy awaits you. Will you fight for freedom or domination? May the force be with you! The v59 is a saber based on Luke Skywalker in the Return of the Jedi. It comes with the Hilt, 92cm Blade, Blade plug, Display stand, SD card with an adaptor, Instructions, Allen Key and Grub Screws. The light is an LED 12w RGB (red, green, and blue) which means you get to choose the colour that you want, whenever you want as the blade cycles through. It comes with a safety-protected 3000mAh battery, battery backward protected system, overload system and over-discharge system. The speaker is 2-3watts, 4/8 ohm which gives a fantastic quality. Features include Pre power on, Blaster, Lockup, Flash on clash, a selection of sound fonts, Volume adjustment, Light effective adjustment, Music, and smooth swing. Blade size is 92cm long, 2mm thick, and 1 OD removable bullet tip. Press and hold the LED button to bring you out of sleep mode. You will hear a "power on" voice and the LED button will turn on. Press and hold the button once, quickly, to turn the blade on. The following controls activate when the blade is on and are based on the flash of the LED button light.

A quick press will initiate a single blaster deflect effect. Press and hold the button for one flash, then release. This will initiate the lockup effect.

A quick press will end the lockup effect. Press and hold the button for two flashes, then release. This will initiate the colour cycle.

A quick press will end the cycle when the colour you want shows. Press and hold the button for 3 flashes to enter the quick colour select.

When a colour you like appears, press the button once to exit. Press and hold past three flashes to shut off the blade. While the blade is off, the following controls are activated based on the flash of the LED button light.

This will change the volume. There are 3 settings: Volume high, Volume low and mute. This will change the blade effect.

There are 3 blade effects: Steady, Pulse and Unstable. Press and hold the button for three flashes, then release.

This will change the sound font to the next selection. Press and continue to hold past the third flash for approximately 10 seconds to put the saber back into sleep mode. You mustn't let the battery fully discharge so our advice is to fully charge the saber when it says low battery or if you haven't used it in a while. Same as RGB apart from. 50w RGB Neopixel Strip in the polycarbonate blade - blade is also 3mm thick. 3600mAh 18650 3.7v safety-protected battery.

SD card to change sound fonts and carry out firmware updates (updates can be provided on request). Extra features like Fire blade, Rainbow Blade, and Ghost blade.

As well as additional light features (demonstration video available on request). This will initiate the drag effect. A quick press will end the drag effect. A quick press will end the colour cycle when the colour you want shows. Continue and hold past two flashes to turn off the blade.

There are a selection of blade effects including but not limited to: Steady, Pulse, Rainbow blade, Unstable and Fire blade. This will change the blade mode. There are several blade modes and ignitions, including some pre-on effects. The blade effect will affect pre-on's will not have any effects on Blaster blade and Ghost blade modes. Only blade colour and font selection impact these modes.

Press and hold the button for four flashes, then release. This will change the sound font.

The selection of fonts can be customized by the user. There are several motions or manual controls available on the Xenopixel. A direct and quick stabbing motion with the hilt level will turn the blade on or off. A quick twist while the hilt is pointed down will change the font to the next on the list.

Either direction will prompt the change if the hilt is pointed downwards. Hold the button and impact the hilt/blade to activate lockup. Release the button to end lockup. A quick twist while the hilt is pointed down will change the selected blade colour while holding the button.

Release the button to select the current colour. While holding the button, a quick twist while the hilt is pointing up will play a special effect. This will also play a sound if the correct file is included in the font. What to do when you first get your new saber.

When you get your new saber, please immediately put it on charge. While it is on charge have a read of the instructions. It's going to take a few tries to get used to all the features via the control button but when you do it is easy. We are available for help and support if you are having any issues learning how to use the features. We will send it with the most appropriate courier.

We will send the saber within 12 hours of ordering. We hope there are no delays in you receiving your order however we will upload tracking so that you can keep an eye on it. If you have caused some accidental damage, we will still be able to help i. If you have snapped the blade, we can replace it at a discounted price.

This product is not a toy Lightsaber so taking the time to learn how to handle and use the features properly is advised. Fully charge the saber before operating. Use only the included cable with 5v1a USB or 5v Wall charger.

Failure to follow this instruction can result in damaged electronics. Domms sabers have no association with Star Wars, Lucas Film or Disney.

Our Lightsabers are not affiliated with the Star Wars franchise. A Range Of Colours To Choose From. A Heavy duelling aluminium alloy hilt with a high quality blade.

For True Fans Who Appreciate A Quality Saber. We are lightsaber fanatics and love that we get to sell some awesome sabers. We started as an emporium and are transitioning into a lightsaber specialist. Every month we are expanding our range to ensure we have a variety of lightsabers available for quick dispatch from the UK rather than waiting weeks from overseas.

Thanks for stopping by and supporting us on our journey. We deliver to any address in the UK, as well as internationally. It is in original undamaged packaging with all tags intact. The product is in the same condition as how you received it. You have a statutory duty to take reasonable care of our goods whilst they are in your possession and during transit. His communication is great and he has a good understanding of the buyers perspective when purchasing something so expensive.

He is also a really nice guy that makes sure the quality of his products are sublime. The lightsaber is bright, easy to use and strong. This item is in the category "Collectables\Science Fiction Collectables\Star Wars Collectables\Lightsaber & Weapon Replicas". The seller is "domms_emporium" and is located in this country: GB. This item can be shipped to United Kingdom.

Character: Luke Skywalker
Film: VI:Return of the Jedi
Color: Silver
Range: Xenopixel
Franchise: Star Wars
Modified Item: No
Vintage: No
Brand: Damien Technologies
Series: Clone Wars
Type: Lightsaber
Year: 2020
Genre: Science Fiction
Country/Region of Manufacture: China
Product Line: Luke